Randy’s Path + Electronic Nectar Collector
You’ve come to appreciate the nectar collector, and now its even better! The Path Plus features a clog-resistant design that allows the device to be readily checked and cleaned in order to avoid clogging. We’ve also included a silicone water pipe connector with your Path Plus, so you can add water filtration to your session whenever you choose. The Path Plus is a must-have for any concentration enthusiast.
The Randy’s Path Plus will fast become the greatest electronic nectar collector on the market, thanks to an upgraded design that eliminates clogging concerns and the addition of a new water pipe connector.
Hook the included Water Pipe Adapter from the Randy’s Path Plus to your favorite glass bong or dab rig to take your dabbing experiences to the next level! Clean, tasty hits are guaranteed when you run your dab vapor through water and percs.
- Battery mAh: 650mAh
- Time to charge battery: 1.5 hours
- Voltage range: 3.3-4.2v
- Time for device to heat up: 10s to temp
- Atomizer capacity: 0.7 mL
- Resistance: 2ohm
- Kit includes: Path Plus Vaporizer, Glass pass through, water pipe adapter kit, usb charger, cleaning brush, instruction manual
Benefits Of the Path Plus:
- Variable Voltage-The Randy’s Path Plus allows you maximum control over the intensity of your dabbing profiles with three temperature settings just a few button clicks away. The Path Plus has three temperature presets (3.2v, 3.6v, and 4.1v), which are represented by colored LED lights around the power button and may be used to vaporize any amount of concentrates at any viscosity. Lower temperature settings, like as 3.2v, are great for flavor enthusiasts or even beginners who don’t want to produce big clouds of vapor right away. Even the most professional dabber can handle higher temps, such as the 4.1v. The Randy’s Path Plus is a wonderful pick for taking your dabbing experience to the next level, regardless of temperature.
Pre Heat And Sesh Mode-When you’re ready to plunge into your dabs, whether alone or with pals, the Randy’s Path Plus has a Preheat & Sesh mode that keeps your e-straw at the right temperature and ready for any dabbing.
To start preheat and enter Nectar Session mode, simply push the Path Plus’s button two times. As the button warms up, the colored light near it will begin to blink, flashing the color of the selected Voltage level. With a simple push of the button, the temperature can be altered. The light will stop flashing and remain illuminated after the initial 15 seconds of pre-heating, and the Path will hold the current temperature for 30 seconds. If 30 seconds isn’t long enough, tap the button three times more to restart the session. If you’re finished while sesh mode is still active, push the button three times to turn off the heating.
Standard Randy’s Path Plus Controls
- Turn On/Off: 5 Clicks
- Change Heat Setting: 3 Clicks
- Engage Preheat / Sesh Mode: 2 Clicks
Nectar Session Button Controls
- Begin Preheat & Sesh Mode: 2 Clicks
- (When Sesh Mode is Over) Extend Sesh Mode: 2 Clicks
- (While Sesh Mode is Active) End Sesh Mode: 1 Click
Indicators And Troubleshooting-
Normal Use Indicators
- Full Battery: Green Light while charging
- Indication of Low Battery: 10 Yellow Flashes
Warnings & Troubleshooting
- 5 Red Flashes: No Tip or Cartridge detected.
- 5 Purple Flashes: Device Overheated
- Let Path cool down (10 minutes) before next use.
- 8 Red Flashes: Short Circuit
- Contact Warranty.
- 12 Red Flashes: Coil Overloaded
- 2 colored flashes of current heat setting: Session time expired.
How To Best Use Your Randys Path Plus-
Attaching a 510 Cartridge
- Make sure that the quartz tip is fully cooled down.
- Unscrew the quartz tip counter clockwise.
- Attach 510 cartridge and screw cartridge on clockwise. Make sure not to over tighten.
- Select desired voltage.
How to use Electronic Nectar Session
- Ensure the device is on (5 clicks) and select desired voltage setting (3 clicks).
- Press the button 2 times to start Nectar Session.
- In Nectar Session Mode, the device will keep heating for 15 seconds (indicated by flashing light).
- Once the device is preheated, it will stay to temperature for 30 seconds (indicated by solid light).
- Press coil to your concentrates.
- During Nectar Session Mode, press the button 1 time to end session.
How to use a Cartridge or other 510 Threaded Accessory
- Press the button 5 times to turn on/off.
- Press the button 3 times to change the setting
- Low: Green: 3.2v
- Medium: Yellow: 3.6v
- High: Red: 4.1v
- Hold the button for 3 seconds to start heating (20 second max cycle)
- Will return to Low Setting after preheated cycle.